Mechanical/Enclosure Development

91 topics in this forum

1. READ THIS BEFORE POSTING

   By John Teel, March 10, 2020
   • 0 replies
   • 99 views
   • 
   • John Teel
   • March 10, 2020

2. Pulley design that can tolerate misalignment

   By Luke Mayhew, Sunday at 06:51 PM
   • 3 replies
   • 21 views
   • 
   • Dave Millman
   • 46 minutes ago

3. Rotomolding vs. structural foam molding for large enclosure

   By Dennis, September 14
   • 0 replies
   • 21 views
   • 
   • Dennis
   • September 14

4. Backlash between rotational axe and a fixed support

   By ZINE, September 4
   • 5 replies
   • 53 views
   • 
   • ZINE
   • September 13

5. How to make an LED to show through opaque black waterproof enclosure

   By RinkerLand, September 9
   • 1 reply
   • 16 views
   • 
   • Christian Theill
   • September 9

6. Can membrane switch overlays be applied to curved surfaces

   By RinkerLand, September 1
   • 2 replies
   • 21 views
   • 
   • Shawn Litingtun
   • September 8

7. How can I ensure my product design won't price out my market in the future?

   By Barry Holleran, August 31
   • 6 replies
   • 49 views
   • 
   • Barry Holleran
   • September 6

8. How to cut perfect holes on ABS electrical enclosure

   By Miguel Hernandez, July 7
   • 4 replies
   • 52 views
   • 
   • Jeff Skarda
   • August 26

9. Choice of prototyping materials and suppliers

   By ZINE, August 20
   • 6 replies
   • 84 views
   • 
   • davidelvig
   • August 22

10. Controller "Middle Door" cut out and buttons

    By RAYMOND CLAUNCH, February 22
    • 7 replies
    • 48 views
    • 
    • RAYMOND CLAUNCH
    • August 18

11. NSF and UL Certification Requirement guidance for Mechanical and Electrical Design

    By Jigar Patel, August 18
    • 0 replies
    • 14 views
    • 
    • Jigar Patel
    • August 18

12. Designing an enclosure for a board with a 3D_PIFA antenna

    By Paul Nykamp, August 7
    • 3 replies
    • 27 views
    • 
    • Paul Nykamp
    • August 16

13. off shelf low cost wifi enabled temp sensor?

    By James Scaggs, July 23
    • 1 reply
    • 31 views
    • 
    • Shawn Litingtun
    • July 26

14. Screws free canister design

    By AE104, July 15
    • 8 replies
    • 66 views
    • 
    • AE104
    • July 18

15. When and How to deal with heat, cold, and condensation in an electronic device

    By RinkerLand, June 7
    • 6 replies
    • 62 views
    • 
    • wayne.frick
    • July 16

16. Choosing a designer

    By Alex, July 3
    • 12 replies
    • 227 views
    • 
    • davidelvig
    • July 10

17. How to draw the product design sketch?

    By Chong Zhang, February 9
    • 5 replies
    • 80 views
    • 
    • Pip Cartwright
    • July 1

18. How to pull up an NIV Mask?

    By Ayush Sharma, June 24
    • 1 reply
    • 29 views
    • 
    • Alex Berrou
    • June 24

19. Where to find good injection molding for Earbuds Housing

    By Rohit Sahay, June 15
    • 6 replies
    • 59 views
    • 
    • Rohit Sahay
    • June 23

20. Mounting small screens

    By Alex, April 4
    • 4 replies
    • 60 views
    • 
    • MikeM
    • June 8

21. PCB housing with Velcro backing

    By Alex, March 12   

    • iot
    • 9 replies
    • 67 views
    • 
    • Alex
    • March 17

22. Best Option for LED Ring

    By smartblinds, August 31, 2020
    • 7 replies
    • 90 views
    • 
    • Jason LeBlanc
    • March 4

23. Design a heating cup

    By shraddha agrawal, January 9
    • 10 replies
    • 64 views
    • 
    • shraddha agrawal
    • March 2

24. Cooling the electronics in a waterproof enclosure

    By Dominic, January 20
    • 6 replies
    • 92 views
    • 
    • Dominic
    • February 12

25. Developing fix pour liquid bottle cap

    By Ayush Jain, February 2
    • 1 reply
    • 27 views
    • 
    • John Teel
    • February 6