Jump to content

Manufacturing

This forum is for discussing manufacturing processes.

150 topics in this forum

  1. How Do I Approach Assembly?

    By darren.riva@gmail.com,
    • 5 replies
    • 175 views

  2. How Do I Approach In House Low Volume Production As A Small Hardware Startup and What Equipment Should I get?

    By sesitechgh,
    • 9 replies
    • 226 views

  3. How to apply wide tapes without air bubbles?

    By fisherman188,
    • 1 reply
    • 21 views

  4. How to clean plastic tubes/polish - in production quantities

    By fisherman188,
    • 9 replies
    • 53 views

  5. How to embed measurement electrodes in PCB?

    By drk,
    • 2 replies
    • 39 views

  6. How to get started with low-volume production

    By Stijn Wielandt,
    • 8 replies
    • 404 views

  7. How to manage risk with PCB's manufacturing and assembly

    By NickS,
    • 4 replies
    • 118 views

  8. How to QC speaker order? Need specifics and to reduce scrap percentage.

    By fisherman188,
    • 13 replies
    • 59 views

  9. ICT/Programming fixtures

    By Craig Scott,
    • 6 replies
    • 96 views

  10. Ideas for a collapsible box/bag usable as a glovebox for TIG welding?

    By fisherman188,
    • 3 replies
    • 16 views

  11. Industrial Design Not translating properly to Silicon Molding

    By Ramy Soliman,   
    • 11 replies
    • 190 views

  12. Info on an Automatic Screwdriver/fastener gun for quick assembly

    By Sam@Congruent,
    • 2 replies
    • 82 views

  13. Injection Molding | Mold flow & strength

    By Kay,
    • 3 replies
    • 70 views

  14. Injection Molding Alternatives

    By haasg,
    • 9 replies
    • 245 views

  15. Injection Molding Cost estimation

    By Dainius Narsutis,
    • 3 replies
    • 70 views

  16. Injection Mould Ownership Document

    By Roberto Weiser,
    • 4 replies
    • 82 views

  17. Injection moulding

    By Trevmar,
    • 9 replies
    • 158 views

  18. It's not over until the Jig is up

    By Scott Shwarts,
    • 5 replies
    • 240 views

  19. Just got this email about 3d printed injection molding from RapidMade...

    By Michael Shonle,
    • 4 replies
    • 60 views

  20. Labelling requirements for battery and wifi enabled products

    By sukhvirdhillon,
    • 9 replies
    • 77 views

  21. Light Bulb - Can't find any E26 Base Screw or GU10 Base Pin Suppliers?

    By Patt O'Brien,
    • 1 reply
    • 62 views

  22. Looking for manufacturing process to embed COB LED on a rigid PCB. Examples Shown (Update -> PCB's Delivered. PCB Rigidity Question)

    By taylorsimoneaux,
    • 14 replies
    • 135 views

  23. Looking to prototype device on Raspberry pi based

    By Farhan Qaisar,
    • 8 replies
    • 78 views

  24. Low quantity to high quantity costs

    By GregB,
    • 3 replies
    • 72 views

  25. Low Volume Enclosures

    By Elliot Slater,
    • 12 replies
    • 249 views
×
×
  • Create New...